High resistivity measurement of SiC wafers using different techniques

To establish fast, nondestructive, and inexpensive methods for resistivity measurements of SiC wafers, different resistivity-measurement techniques were tested for characterization of semi-insulating SiC wafers, namely, the four-point probe method with removable graphite contacts, the van der Pauw method with annealed metal and diffused contacts, the current-voltage (I-V) technique, and the contactless resistivity-measurement method. Comparison of different techniques is presented. The resistivity values of the semi-insulating SiC wafer measured using different techniques agree fairly well. As a result, application of removable graphite contacts is proposed for fast and nondestructive resistivity measurement of SiC wafers using the four-point probe method. High-temperature van der Pauw and room-temperature Hall characterization for the tested semi-insulating SiC wafer was also obtained and reported in this work.     

微区电阻测试方法及新测试仪研制

文章对国内外开展微区薄层电阻测试的方法进行了综述，特别对改进范德堡四探针技术方法的测试原理、测试过程与测试结果进行了论述与分析，对微区电阻测试方法的进一步发展提出了一种可操作的方法，并研制出新型四探针测试样机。     

Many-Body Terms in van der Waals Cohesion Energy of Nanotubes

We have developed a model for the calculation of van der Waals force for layered systems with axial symmetry. Our result can be applied to compute the cohesion of a carbon nanotube to a substrate, the cohesion between nanotubes, and between shells of multiwall nanotubes. We have obtained unusal power laws for the distance dependence of the many-body van der Waals potential.     

秦山核电厂蒸汽发生器带钧波形板蒸汽干燥器的设计

文中详细介绍了秦山核电厂蒸汽发生器带钩波形板蒸汽干燥器的设计观点。     

EFFECTS OF SUBMICROMETER PARTICULATE SILICA ADDENDA ON THE ADHESION OF MICROMETER-SIZE PARTICLES TO A POLYESTER-COMPOSITE SUBSTRATE

The force needed to detach five sets of different size particles, having number-averaged diameters between 3.6 and 8.5 µm, from a composite substrate was measured using an ultracentrifuge. In addition to size variations, the asperity concentration for each size particle was adjusted by varying the silica concentration, adjusted so that the surface area concentration at each level was kept constant for the five sizes of particles. Due to the changing silica concentration and particle size, the charge per particle also varied. It was found that the detachment force appeared to be virtually independent of charge, with any correlation actually appearing slightly negative, if anything. However, the detachment force increased monotonically with increasing particle diameter and decreased monotonically with increasing silica concentration. Moreover, upon normalizing the detachment force to the particle diameter and the silica concentration to the surface area concentration of silica, it was found that the detachment force clustered into groups in which the force needed to separate the particle from the substrate depended only on the silica concentration. These results suggest that van der Waals interaction, rather than electrostatic forces, are the dominant mechanism controlling toner adhesion in this instance.     

Accurate higher-order analytical approximate solutions to nonconservative nonlinear oscillators and application to van der Pol damped oscillators

In general, this paper deals with general nonlinear oscillations of a nonconservative and single degree-of-freedom system with odd nonlinearity and, in particular, it presents accurate higher-order analytical approximate solutions to van der Pol damped nonlinear oscillators having odd nonlinearity and the Rayleigh equation. By combining the linearization of the governing equation with harmonic balancing and the method of averaging, we establish accurate analytical approximate solutions for the general weakly damped nonlinear systems. Unlike the classical harmonic balance method, simple linear algebraic equations instead of nonlinear algebraic equations are obtained upon linearization prior to harmonic balancing. The combination of these two methods results in very accurate transient response of the periodic solution. In addition and for the first time, this paper also presents a method for deducing fourth-, fifth- and higher-order linearized governing equations from the lower-order equations without the requirement of formulating the problem from the first principle. Three examples including the van der Pol damped nonlinear oscillator are presented to illustrate the excellent agreement with approximate solution using the exact frequency.     

Determining the life cycle of bolts using a local approach and the Dang Van criterion

The fatigue behaviour of bolts under axial load has always been considered from the component point of view for which fatigue limit is usually taken equal to 50 MPa, and few results are available to designers for limited lifetimes. Here, we take up this problem from a material point of view using a local approach. For each case of fatigue testing, using finite‐element (FE) model of the bolt, we determine the stabilized local stress at the root of the first thread in contact with the nut. To characterize bolt behaviour with these numerical results, we use Dang Van multiaxial fatigue criterion for which we extend application to the medium fatigue life. These results can be correlated with the experimental numbers of cycles to failure to determine material parameters of the generalized criterion. Using statistical Gauss method, we can make lifetime predictions for any level of risk of failure. In addition, we propose an analytical model to rapidly determine the local stress condition from nominal loading data (mean stress and alternating stress). This model dispenses us from a new modelling if the bolt is stressed in the same manner as the bolts used for behaviour characterization. Using this model and the generalized criterion, it is extremely easy to make lifetime predictions whatever the risk considered.     

Aluminum. II. Derivation of C v0from C p and comparison to C v0 calculated from anharmonic models

The specific heat at constant pressure, C _p, of aluminum measured by Ditmars, Plint, and Shukla has been reduced to the volume V ₀ appropriate for 0 K employing the Murnaghan equation. The C _v0 thus obtained is compared with the theoretical C _v0 calculated in the harmonic and the lowest-order anharmonic approximation from three different pseudopotentials (Harrison, Ashcroft, and Dagens-Rasolt-Taylor) as well as a phenomenological Morse potential. The higher-order ( ⁴) anharmonic contributions are calculated from the same nearest-neighbor Morse potential as in the lowest-order anharmonic theory. The role of the vacancy and the higher-order anharmonic contributions to C _v0 has been examined and we conclude that the ⁴ contributions to C _v0 are much smaller than the vacancy contribution. After removal of the vacancy contribution, the reduced C _v0 is found to be in excellent agreement with the Ashcroft and Harrison pseudopotentials as well as the Morse potential including the ² and ⁴ contributions to C _v0.     

用局部法评定焊接接头的疲劳性能

采用16Mn钢非承载十字焊接接头疲劳试验结果对使用Dang Van准则的疲劳评定局部方法进行了研究。结果表明，有限元分析中应力集中区单元尺寸对局部参量计算有明显影响，为获得比较合理的预测结果需对焊趾应力集中区所划分的单元尺寸限定，当接头焊趾半径在0．15-0．8mm变化时应选择最小单元尺寸0．32-0．62mm计算局部参量；在此基础上Dang Van准则可以对焊态接头做出合理的评定，但Dang Van建议的卢值偏安全。此外，通过计算发现焊趾半径只影响局部很小区域(约0．5mm内)的应力集中分布，在某一深度(约0．5mm)后存在稳定的应力集中，因而建议采用距应力集中区最大应力处某一深度的应力参数计算Dang Van局部参量可能更为合理，这将减小局部参数对焊趾半径及单元尺寸的依赖性。